Please visit our home site at www.TRILOBOATS.com.

Anke and I live aboard WAYWARD, and wrote about it's design and construction at ABargeInTheMaking.blogspot.com.

Access to the net comes and goes, so I'll be writing in fits and spurts.Please feel free to browse the archives, leave comments where you will and write... I'll respond as I can.

Fair winds!

Dave and Anke
triloboats swirly gmail daughter com

Saturday, February 6, 2016

Footwear's Footprint: Problems and a Solution?

Tire Sandals.

From Thomas J. Elpel's Primitive Living Skills
Article contains tire sandal pattern and instructions
 

Sell a man a boot, you boot him for a while.
Teach a man to boot, you boot him for life.

-- Ancient Chinese saying, sort of 

 Footwear's Footprint: Problems and a Solution?


As coastal cruisers in temperate climes, we are oppressed by our mountain of footwear.

Here's our current list by type and purpose; 
  • Rubber Boots Edge-of-the-water and wet hikes ashore.
  • Leather Boots – Longer, more rugged hikes.
  • Hip Waders – Wading for repairs or thin water maneuvers... chest waders would be nice, instead.
  • Winter Boots – Insulated for cold weather sailing or snow ashore.
  • Sandals – In and out of water in warm weather... good soles allow doubling as street shoes.
  • Slippers – Sheerling for lounging and fair-weather sailing, while high soles allow short, wet deck excursions.
  • Snow Shoes – Snow and occasionally mud.

Times two! Sheesh!! This adds up to a bulky heap o' gear.

Shoes get a lot of wear and tear, and replacing them adds up, over time, to a pretty penny. 

If not given prime storage, they tend to mildew, no matter how well cleaned.
Our vital rubber boots, in particular, only last a few seasons at best... we face a choice of carrying a spare set or patching (mixed success) until pulling into a town for replacement. And over the years, they leave a trail of unrecyclable garbage. Can sometimes cut them down to 'garden loafers' and pass out to friends, but most of them are doing the same, themselves.

My hip waders are heavy rubber whose tops fold down and up again, like old-fashioned sea-boots (this makes them near impossible to use with pant-style raingear, and a short rainjacket doesn't cover their tops). While I like them in dry weather, they are too heavy and expensive for general use. Anke uses a lighter set, but they're still not economical for frequent use.

In general, we go for robust treads for afloat/ashore use. Not for us the sliced sole, deck-gripping yacht tread... they just can't cope with a slimy rock or mossy log.

But I've come across some ideas that might help reduce our footprint.

Leather has some distinct advantages, with DIY potential.

Well made, maintained and oiled, leather boots are reliably waterproof. Irving Johnson, in Around the Horn, reports that professional sailors preferred leather sea-boots to rubber. Apparently, they kept feet warmer and overall dryer. I'm guessing it's because rubber doesn't breath, and feet are soon dampened from condensation, even on dry days. 

Boot leather is tough stuff. We wear out our resole-able rubber treads, but the uppers just keep on going.

A friend directed me to this brilliant idea: 

Make DIY sandals from old tires. Add a moccasin. Add good socks. Go. 

This system has been reported to be extraordinarily comfortable on thousand plus mile treks in rugged terrain. In our case, we'd be looking at boot moccasins (or moc + tall, waterproof socks?). 

It's a modular system (my favorite), which confers high versatility. Each component can be used separately or in combination. The sandals provide solid, sure, cheap soles to the boot mocs, while the socks layer up to moderate weather.

In our case, we would need the boot leather to be selected, treated and built for waterproof service. At best, waterproofness is pursued from the tanning process on. 

To this basic system, I would like to add a roll of light, water-proof or -resistant fabric to the boot top. Waxed cotton, for example, dampens when immersed, but will not flood through. It would normally be worn furled, but could be unrolled as hip-waders. This avoids the weight and volume issues of folded leather. Having them always available would be a big asset. 

Insulated overboots from sturdy fabric for cold-weather can be DIYed, again using the sandals for soles. Weather cold enough for insulation is generally dry. With care, these can be used ashore. With luck, the overboot could double as a lounging slipper?

In-soles are a low-profile accessory. Wool insoles provide cushion and insulation from the ground without over insulating the foot above. Specialized insoles increase shock absorption. 

The only sticking point is that, while moccasins are easily made by the home craftsperson, waterproof moccasins are not (they can be DIYed, but it's skilled work). There are a few professionals who offer these, custom made, but they cost considerably more than one normally expects to pay for common footwear. 

Still, I'm guessing that a custom crafted boot moc will pay for itself with decades of life if faithfully protected by the sandals. We waffle, but my guess is that this is one skill we'll not acquire unless forced by circumstance.

If this works, we'd be down to the modular system and snowshoes... 

That's more like it! 


15 comments:

  1. Right now I own a pair of flip flops and one leather hiking sandal. I've been giving serious thought on how to get by with the minimum of footwear, since I have to start over.

    ReplyDelete
    Replies
    1. Hi Sixbears,

      I'd say I'm jealous of your footwear, but just heard of your vessel's loss. So glad to hear no one was hurt, but feel for you and your lovely wife.

      ZOON (one of ours) sunk to her decks and tossed her cookies... we had an easier recovery than you, but it wasn't what we had in mind! So we have an idea what you're going through.

      You might consider a donation button at sixbearsinthewoods.blogspot.com?

      Dave Z

      Delete
    2. Sixbears,

      Good to see you back here.

      Yoda

      Delete
  2. Very sorry about your misfortune Sixbears. I hope you and your wife have as successful and easy a recovery as possible.
    Dave, I wonder if the approach of old fashioned footwear like putees made of wool or synthetic fleece might have some use. The Russians certainly considered them to be worthwhile and they suffer harsh winters. While they aren't waterproof wool does have the merit of maintaining warmth while wet. They don't have to be a set size either. They could be matched with the sandal approach. The Scottish certainly went with the idea that it was easier to have shoes which let water out than it was to keep it out.

    ReplyDelete
    Replies
    1. I should add I mean the sort which wrap the whole foot. Not just the gaiters like type.

      Delete
  3. Hi Tassiebush,

    I think those make a great sock and slipper, and maybe a kind of moccasin as well? Certainly would work well with the sandal, as well.

    The old Norwegian fisherfolk, hereabouts, used boiled wool socks (in boots) and mittens. They'd throw the mitts in a pan of water on the exhaust manifold on their way to the grounds, then working all day in seawater and icing fish.

    Boiled wool is simply that. Knit oversize with a lofty pattern, then boil to shrink for very tight, dense fabric (tougher, too). Felting can be involved between yarns, or go felt from the start, and skip the knit.

    My problem as regards such open solutions is slender extremities with poor circulation. I'm afraid I would be quickly culled by natural selection without dry and warm feet and hands! 8)

    Dave Z

    ReplyDelete
  4. I completely identify with the desire to stay dry. It will always be the best option. Chillblains and worse are best avoided being warm and dry. Interesting about the Norwegian practices. Makes a lot of sense. Felt is a fantastic material.

    ReplyDelete
  5. I could really get into the idea of modular shoes, though first choice would be Sixbear's plan -- flip flops, sandals, and when pressed, one more something. Maybe hiking boots.

    Dave, for your tire tread sandals, I'm wondering about your strap attachment points. Cutting the tire rubber to shape is easy enough, but getting straps to stay on is bit trickier. My favorite footwear is Teva sandals (and boots), but even those world-renowned people can't figure out how to keep the soles from coming off / apart (their only drawback).

    If the plan is gluing two rubber soles together in a sandwich, it better be some wicked strong glue.

    ReplyDelete
    Replies
    1. Hi Yoda,

      These guys I referenced are using tabs cut and slotted from the tire itself (you can see them in the picture, coming up the sides).

      I haven't heard of any problems with these, and imagine they're pretty tough, so long as good margins are maintained.

      A lot of commercial sandals tend to the ultra-light weight school. I can see the advantages of light footwear, but, carried too far, it often seems to have more to do with planned obsolescence!

      Dave Z

      Delete
    2. I know this is an old thread but if, like me, you recently discovered this site. I wanted to add to this conversation.

      I have been making similar sandals from old or damaged fat bike tires for years. The tires need to be true "fat" bike(bicycle) tires at least 3". After the tire is worn out or you damage a side wall, cut off the side walls so you have the contact portion and use it for flexible sandals. I follow this guide: https://xeroshoes.com/how-to-make-huaraches/ and this other page from them shows different tying variations: https://xeroshoes.com/tying/

      They work great for foot protection against pointies and thornies. If you made the strings/straps adjustable you could tie them tighter when barefoot or looser with a moccasin underneath.

      The best part is old fat bike tires or car tires are free and string is cheap.

      Abie Hoffman also had a guide for using car tires and bicycle inner tubes in his book "Steal this Book". He called them Ho chi Minh sandals.

      This is my preffered footwear and I have been trying to figure out how to make them more versatile and you guys have been throwing out great ideas. I like the leather "boots" with canvas tops idea.

      And dave this is a fantastic site, I hope to buy plans and build one of your boats in the near future. I need to get back on the water.

      Delete
    3. Hi,

      Great to hear of your experience! Fat bike tires are a great idea. We've only seen one, so far, but we've been out of circulation a while. They sound like the perfect fit, so to speak.

      I'm still waiting for my last pair of normal boots to wear out before making the leap, but the day is coming soon.

      Glad you're liking the sites, and c'mon - the water is loverly!

      Dave Z

      Delete
  6. "Build a man a fire, and you warm him for an hour.
    Set a man on fire and you warm him for the rest of his life!"

    ReplyDelete
  7. Good old barge cement has been used to glue boot soles for years, and as a tire patch is essentially glued on with the same contact adhesive sandwiching isn’t a real issue.
    For my own experiments I find motorcycle tires to be best, as they are still bias ply (no steel belt) and thinner. I have had success gluing and then sewing soles to bag shoes or as foundations for moccasins works well.
    As to sandles. Some South American tribes just put a not in a string and reses it in the tread wile south East Asians use inertube and a thin slot. Some of the hiking sandles I have seen cut tabs on the sides and shave of the tread almost to the ply, slotting in straps.
    If one needed boots one need look no further than the mop boot used for NBC/ABC gear. Asentualy a rectangle of tread with side and toe tabs attached to a rectangular bag. No right/left and one used a lace to fold over the toe and secure the boot. A leather or canvace bag works equally well or a hunk of inner tube and barge cement (contact adhesive for counters works about as well).
    Lots of ways to skin a cat, and our ancestors have been making foot gear for a few thousand years on atleast 6 contenents.

    ReplyDelete
  8. Hi Charles,

    Lots of good info in your comment, and it sounds as though yours is a voice of experience.

    MOPP gear approaches look very interesting. I'm not sure we could stay nimble in simple rectangles, but they seem a good place to start. I like the 'bag' uppers, as nearly within my skill set. 8)

    Dave Z

    ReplyDelete